Tek Gel for Profiling

Product code numbers:
TGP101 (1-gallon)
TGP105 (5-gallon)
TGP155 (55-gallon drum)

› Surface Gel Tel Product Catalog (PDF)

› Profiling and Cleaning Large Areas
› Profiling Mold
› Profiling Rust

SGT has developed a new method of treating concrete surfaces. This methodology is protected by a US Patent and know-how and is a new technological development having a defined need in the market place.

Because Tek Gel™ for Profiling is gelled, it can be readily applied to flat, angled, round and inverted surfaces with minimal run-off. This allows for longer and in some cases, unlimited contact time thereby increasing the activity and efficacy of the product. It can also be concentrated in specific areas without effecting the remainder of the surface, if so desired.

Tek Gel™ for Profiling gelled acid products can be applied by spraying, brushing or rolling onto the surface to be treated. It is within the scope of the patent that the surface may be immersed into the product to obtain adequate cleaning, i.e. bolts, tools ect. for rust removal. The products are left in contact with the surface for 3-5 minutes in order to acquire a uniform profiled or treated surface.

After effectively profiling the concrete surface, the products are easily and readily rinsed away with water. The products are water-soluble and do not leave any soap, slick, slime or other residues on the surface. The products do not alter the pH of the concrete surface and therefore do not require neutralization, thereby eliminating a potentially expensive and time consuming operation.

The use of acids in concrete treatment products and in many manufacturing processes has until now, lacked important and beneficial characteristics which are avilable with SGT's patented technology. The gelled acids, commericalized by SGT may be produced at high viscosity levels and lower acid concentrations, while continuing to maintain efficacy because of increased contact lime. This characteristic also reflects the ability to create highly effictive acid products that are safer for application by the end user and safer to the enviroment.

Because the scope and parameters of this patented technology are extreamly broad and may encompass a broad spectrum of acid concentration ranges, compositions can be produced ulitizing a plurality of different acids or active ingredients. Designer products in which the viscosity gel to a thick gel, to a putty-like or near solid, can be created to provide the needs of specific end users and niche markets.

PRODUCT DESCRIPTION: TEK GEL™ for Profiling
Concrete Surface Preparation and Treatment

Gelled Acid Formula:	Hydrochloric (HCl) 18-25%
Color:	Opaque gel
Odor:	Mild pungent
pH:	+/- 1
Solubility:	Infinite in water
Flammability:	Non-flammable
Flash Point:	> 200˚C
Freeze/Thaw:	Store between 38˚F & 100˚F
Coverage:	200 - 400 sq. ft. /gal.
Storage:	Stable under normal conditions.Do not store near or mix with strong alkalis, i.e., sodium or potassium
User Warning:	Use in well ventilated areas only
Safety Wear:	Splash goggles. Ventilator and neoprene gloves recommended. Avoid excessive direct contact with skin
Health rating:	3 Severe (Corrosive)

DIRECTIONS FOR USE / APPLICATION:

• Ready to use, DO NOT DILUTE
• Remove loose materials from surface
• Shake or stir contents well before applying
• Wet Surface and remove standing water
• Apply with care using an acid resistant brush, sponge, squeegee, roller, or low-pressure acid resistant sprayer
• Allow product to sit on surface 5 - 30 minutes
• Agitate product on surface with stiff brush
• Rinse thoroughly with water; when sufficiently rinsed subsequent neutralizing is not needed
• In extreme cases or if a deep etch is desired, a second application may be needed
• TEK GEL™ for Profiling works best with Portland Cement based concrete.
• Product can be pumped from a container by using an acid resistant hand pump.
• Product must be stirred or mixed well before use, with or without pump.

Read MSDS prior to use.

PRIMARY USE:

• Opens up "steel troweled" concrete surfaces (Profiles the surface)
• Produces a uniform etched surface for improved subsequent product adhesion
• Can be used on new or old concrete surfaces to remove rust, stains, algae, mineral and salts deposits, water parasites, efflorescence, oxidation and other foreign matter from concrete surfaces.

LIMITATIONS/INCOMPATIBILITIES:

• Avoid strong oxidizers, caustics, fabrics, carpets
• Avoid prolonged contact with metals and marble. Caution: If product comes in contact with metals, flush with water to avoid damage.
• If used indoors, provide adequate ventilation
• Humidity increases the need for additional ventilation
• Excessive heat can cause evolution of gaseous hydrogen-chloride
• Avoid continuous direct sunlight
• Avoid freezing
• Do not reuse container. Follow all applicable Local, State, and Federal chemical disposal regulations.

TOP 20 ADVANTAGES of TEK GEL™ for Profiling

1. Ready to use; DO NOT DILUTE
2. Saves time & labor
3. Gelled consistency permits longer contact time
4. Can be applied to flat, vertical & inverted surfaces
5. Opens up "steel troweled" surfaces
6. Increases profiling effectiveness and uniformity
7. Increases bondability
8. Improves warranty on subsequent products
9. Non-abrasive
10. Can utilize in-house craftsman, short training time
11. Job site flexibility
12. Safer for environment & end-user
13. Low fuming, Non-flammable
14. Can be used on new & old concrete
15. Can be used on large & small job sites
16. Removes algae, mineral build-ups, rust, etc.
17. Rinses with water
18. Neutralizes with water
19. Flush to sewer
20. Excellent shelf life

ORDERING INFORMATION:

Packaging: 1, 5, 30 and totes
Weight per gallon: 9.6 lb
DOT: NMFC 44155
IATA: UN1789, Hydrochloric Acid, 8, PGII

PERFORMANCE TIPS:

• Test patch before use is recommended
• Not intended to etch through epoxy coatings or for use on metals.
• Average coverage is 300 sq. ft. per gallon. Coverage rates vary with surface of concrete

WARRANTY SUMMARY:

For complete warranty statement and important limitations, read the MSDS and Warranty Sheet. Generally, Surface Gel Tek, LLC represents and warrants only that its products are of consistent quality. No other oral or written statement is authorized. Any liability is limited to refund or replacement of defective product. The end user shall determine product's suitability and assume all risks and liability.

MANUFACTURE INFORMATION:

Surface Gel Tek, LLC
663 W. 2nd Ave., #15
Mesa, AZ 85210
T: 480-970-4580
TF: 888-872-7759
F: 480-421-6322
Website: www.surfacegeltek.com
Email: info@surfacegeltek.com

Sold Direct and through Distributors

› Return to Products Menu